Are trolling motors worth fixing?
Are trolling motors worth fixing?
Minn Kota 710, 42 Lb.bow mount It turns left and right but just get a click...sounds like a relay...when I want the prop to spin. Are these things throw aways or worth getting repaired if it even can be?
- Cancatchbass
- Gold Participant
- Posts: 1692
- Joined: Fri Jan 10, 2003 4:30 pm
- Location: 1000 Islands
Usually, yes!
There is a Minn Kota Authorized Repair Centre in Kingston. Most parts in stock. Will often fix your unit while you wait. PM me for details, if you want.
CCB
CCB
- SkeeterJohn
- Diamond Participant
- Posts: 2867
- Joined: Wed Nov 27, 2002 7:32 am
- Location: Ottawa
- Rideau_Lungehunter
- Bronze Participant
- Posts: 111
- Joined: Thu Oct 03, 2002 2:45 pm
- Location: Oxford Mills (Kemptville)
- Cancatchbass
- Gold Participant
- Posts: 1692
- Joined: Fri Jan 10, 2003 4:30 pm
- Location: 1000 Islands
Repair centres
One very important thing to keep in mind when dealing with any "Authorized Repair Centre" is the extent of their inventory of parts.
Take your motor to a centre with minimal parts inventory- I believe the minimum Minn Kota will allow is $2,000., which doesn't allow for very many parts- probably a couple of shoe boxes full.
The reason I mentioned the Kingston facility is they keep in stock a minimum of $20,000. in the most commonly needed parts.
It seems some parts often are back-ordered, and, when available, have to make the sometimes long journey from the U.S. to the Canadian head office (where many common parts are stored), then to the service centre. If the part you need is not sitting at the service centre, and you need to be on the water within a few days, you could be working down your honey-do list instead of fishing.
I believe the Kingston facility will also supply loaners (I think so, anyway ) if they are unable to complete the repairs on the spot, while you wait. I didn't test that out, though, since mine was repaired-on my boat- while I waited.
CCB
Take your motor to a centre with minimal parts inventory- I believe the minimum Minn Kota will allow is $2,000., which doesn't allow for very many parts- probably a couple of shoe boxes full.
The reason I mentioned the Kingston facility is they keep in stock a minimum of $20,000. in the most commonly needed parts.
It seems some parts often are back-ordered, and, when available, have to make the sometimes long journey from the U.S. to the Canadian head office (where many common parts are stored), then to the service centre. If the part you need is not sitting at the service centre, and you need to be on the water within a few days, you could be working down your honey-do list instead of fishing.
I believe the Kingston facility will also supply loaners (I think so, anyway ) if they are unable to complete the repairs on the spot, while you wait. I didn't test that out, though, since mine was repaired-on my boat- while I waited.
CCB
- trexellunge
- Bronze Participant
- Posts: 261
- Joined: Mon Sep 15, 2003 7:47 pm
I have the same choice to make regarding my old broken trolling motor (OMC). It's over a decade old, but it's a foot control that I'm comfortable using....I don't even have to think about steering while I'm casting. If it doesn't cost too much, I think I'll get it fixed. I know I'm getting old when I resist change. I bet the new foot controls have made quantum leaps in improvements...maybe I'll get a 2nd boat and keep ol' sparky, along with buying one of the new fancy dandy motors to boot! I'll spend $10,000 on a new boat to save a $200 electric motor! Now that's the kind of math I can understand.
My minn kota started doing the same thing as hosers did last night.. left and right are fine but when prop should be turning there is just a click.
It is a minnn kota power drive 55pd about 4 years old
Anybody have the same problen and if so what was the fix?
CCB can you provide me with some more info on the repair shop in kingston that you mentioned?
thanks
It is a minnn kota power drive 55pd about 4 years old
Anybody have the same problen and if so what was the fix?
CCB can you provide me with some more info on the repair shop in kingston that you mentioned?
thanks
jale....I haven't done anything about mine yet, but talked to these guys on the phone. Good bunch and know their stuff.
THE PROP SHOP
Country: CANADA
800 BURNETT ST
KINGSTON, ON K7M 5V9
Tel: 613-634-7033
Fax: 613-634-7033
Email: thepropshop@bellnet.ca
THE PROP SHOP
Country: CANADA
800 BURNETT ST
KINGSTON, ON K7M 5V9
Tel: 613-634-7033
Fax: 613-634-7033
Email: thepropshop@bellnet.ca
I ended up with a new transom mount 38Lb thrust for about what it would have cost to fix the old bow mount. Works great, but a bit of a pain to keep the boat going straight if it's windy. The worst part is I have to sit in the back of the boat and whoever is with me gets first shot at the fish. Guess that's where the skill comes into play eh?
Minn Kota Maxumm 50
Hi I have a used unit if anyone is looking in to replacing theirs. I had it posted for a month on the Classified but got no bites. I am looking for $250 and I will throw in the extension handle too. It is a transom mount. New alligator clips included also because the old ones are wearing. Good solid package that pushes water like crazy. I just don't need it on my new ride.
PM me if interested.
PM me if interested.
Hoser
I have a 38lb Minkota Endura on my 14 Ft Springbok Pro Series. It is a transom mount but I use it on the bow.
My casting deck is even with the sides of the boat. A piece of steel angle with a piece of 2 x 4 bolted to it makes a nice bracket. Bolt that bracket to your deck, parallelle to the side of the boat. Once the motor is attached to that bracket, you now have a bow mount. The head of the motor needs to be rotated 180 degrees so the propeller point in the right direction in relation with the handle. It simply a screw that you pull out, rotate, and re-insert the screw. Store the battery under the deck. Works awsome.
I can post some pictures if you want.
Let me know
I have a 38lb Minkota Endura on my 14 Ft Springbok Pro Series. It is a transom mount but I use it on the bow.
My casting deck is even with the sides of the boat. A piece of steel angle with a piece of 2 x 4 bolted to it makes a nice bracket. Bolt that bracket to your deck, parallelle to the side of the boat. Once the motor is attached to that bracket, you now have a bow mount. The head of the motor needs to be rotated 180 degrees so the propeller point in the right direction in relation with the handle. It simply a screw that you pull out, rotate, and re-insert the screw. Store the battery under the deck. Works awsome.
I can post some pictures if you want.
Let me know